Nails

General Purpose constuction nail. Supplied in 500g bags.

• Fastners Screws
• Nuts
• Screws
• Bolts
• Screw heads
• Screw Driver
• Mirror Screw
• Torx Screws
• UK Nails
• Black Nails
• Small Nails
• Drywall Screws
• Levers
• Small Screws
• Self Drilling Screws
• Archimedes Screws
• Self Taping Screws
• Cheval Mirror Screw
• 12wood Screws

and more visit our online shop for More.

Installing fence

There are different material options when it comes to fencing, from wood to metal to plastic. For this example we'll talk about the use of pressure-treated wood since it offers long-standing survival. Just take the exact size of your property to the local fencing distributors. Don't worry too much about figuring out how much material you'll need. They will be able to figure out the cost.

Tools needed:

• Safety glasses.
• Air gun nailer (makes the job go faster unless you're REALLY into fluctuation a hammer)
• Post hole digger (if you're ok with blisters) or a power auger (Make sure someone instructs you on how to use the tool, and carefully follow all safety precautions.
• Small sledge hammer
• Type N quick drying cement
• These mechanical beasts don't know the difference between your foot and the ground when they start digging) Shot line

Regardless of the type of wood you use, the nails be supposed to last as long as the fence, so choose galvanized nails if at all possible.

The number and assignment of the posts you use will be determined by the distance of your fence. A good rule of thumb is to space them between 6 to 8 feet apart. Once you've determined post placement, you're ready to dig your holes. The general guideline for setting posts is to place at least one-third of the length of each pole in the ground.

What I like to do is put in my corner posts first and use them as a guide to get all the subsequent posts to line up straight. Set the corner posts where you want them, securing the posts by adding a bag of fast-setting concrete to each hole. Simply add a gallon of water and allow the mixture to set up; it will generally harden in less than an hour. Once a post is placed in the hole, check to see if it's plumb and adjust as necessary. Hold in place by nailing scraps wood to the post to stake it. Once the cement has set tie a piece of shot line between the corner posts as tightly as possible. This is your plumb line for setting up the rest of the posts in straight line.

When insertion the top rail, keep in mind that a good typical height is between 58 and 66 inches from the ground. The center and lower rails should be spaced evenly below. The rail length is resolute by measuring from the center of one post to the center point of the next. Use two 10-penny nails to fasten the end of each rail to each post, making sure that all the rails are on the same horizontal plane and the same distance from the ground.

To speed up the construction process, make sure all the rails are in position before starting to attach the pickets. Place a picket on the first post, with the bottom approximately 1 inch above the ground. Make sure it's plumb, and then nail it in place.

Repeat the process with a picket on the next post, but only nail it in place with one or two nails. Then add a nail to the top of each picket and run a string between them, placing it a half-inch above the top of the picket. The top of each picket should then be positioned a half-inch below the string. This allows the pickets to gradually follow the contour of the yard. Tip: To ensure a uniform space between your pickets, cut a small piece of one picket to use as a spacer as you work your way along the rails. (Be sure to keep placing pickets with the tops a half-inch below the string line.)

While holding each picket in place next to the spacer, secure it with a single nail right in the center. This will allow some leeway for aligning it later. Work your way around the perimeter until each picket is secured with a single center nail.

Now it's time to plumb the pickets. Hold your level alongside and on top of each one to check that it's plumb. Once it's perfectly positioned, get the nail gun and add two nails to the top end (for a total of three, since the first one was put in earlier to hold the piece in place), then secure it with three at the bottom end. Repeat the process all the way down the line, then go to the other side and repeat again.

If you follow all the steps correctly you should end up with a fence that runs straight on all sides, and best all adds to the curb appeal of your home.

Bathrooms Online